Greddy Turbo Timer Install

TURBO TIMER MANUAL




How to wire the Turbo Timer w/ the Turbo Timer Harness

 

How to wire the Turbo Timer w/o the Turbo Timer Harness

 

  1. On the power harness, cut off the large 3-pin connector.

  2. Tap or solder the cut lines of the power harness to the appropriate lines as shown below.





  3. Be sure to ground the black wire to a good ground source.
Important: The Turbo Timer will not function properly if there is a bad ground connection. If grounding to the body, make sure to remove the paint for the best ground.



Optional set-ups

Optional: Connect for Optional Parking Brake Warning
This feature notifies the driver with a "beep" if the key is removed without the parking brake engaged.
  1. Remove the cover for the parking brake. Look for the parking brake switch wire.

  2. If there is only one wire from the switch, check to see: If the wire has: 0V when parking brake is ON 12V when parking brake is OFF If there are two wires from the switch, look for the wire that has: 




    0V when parking brake is ON   12V when parking brake is OFF
  3. Route the "BROWN" wire from the Safety Feature Harness through the center console to the parking brake switch.

  4. Tap the "BROWN" wire to the wire from Step 2.

  5. Reinstall the parking brake cover.


Optional: Connect for Speedometer Signal Feature
This feature will shut the engine off if the vehicle starts to move during "turbo-timing."
  1. Connect the "PURPLE" wire to the speedometer signal wire from the ECU.

  2. Please refer to the factory service manual of the vehicle for the proper signal wire.

  3. This feature should only be attempted by a skilled technician.
Important: GReddy Performance Products, Inc. is not responsible for any damage caused by improper installation of the GReddy Turbo Timer.


IMPORTANT:
Please do not attempt to hold down the POWER switch button while the turbo timer is turned off. This may cause the Turbo Timer to malfunction.



Basic Operation

Start the engine
Music starts
2 seconds later
After 1 minute

During vehicle operation
 

Engine shuts down



Test: Parking Brake Safety Feature

1. Repeat steps 1 through 3 of the basic operation check procedure
2. Step on the foot brake and release the parking brake. Be sure to have the transmission in either neutral or park.
3. Turn the key switch to the OFF position and check to see if the countdown and SND flash alternately. There should also be a beeping sound.

4. Re-engage the parking brake and check to see if the Turbo Timer continues to count down, without the SND flashing and beeping.
5. During countdown, release the parking brake. The engine should then shut down.




Test: Speedometer Signal Safety Feature
Caution: When checking this feature be sure that there are no objects directly in front of or behind the vehicle.

1. Apply the foot brake and release the parking brake.
 
2. Repeat steps 1-4 of the basic operation check procedure. It should count down and snd flash alternately with a "beeping" sound.
3. Then put the vehicle in gear, release the foot brake, and move the vehicle. The engine should then shut down.

This completes the operation check
If the Turbo Timer does not operate properly, first check all of the wire connections, contact the Authorized GReddy Dealer you purchased the turbo timer from for assistance.




How to change the preset time

By pressing the time switch, you can change the time setting.
When the Program Number is displayed.
When the Time is diplayed.
* If you tap the time switch button, the time will increase, by 10 seconds.
* If you hold down the time switch button, the time will increase by l minute.



How to program the preset time

By holding down the select switch, you can save a desired time for both P-1 and/or P-2
1. Set to the desired Preset time setting P-1 or P-2
2. Set the time to desired time by joggling the Time switch button.
3. Hold down the SELECT switch button for 2-3 seconds, until you hear a "beep." The desired time will now be saved in the turbo timer's memory until the battery is disconnected.



How to select the preset time

By pressing the select switch, you can select the 2 preset time settings
Preset Time Setting:
P-1 > 1 minute
P-2 > 3 minute
* To switch to a desired preset time setting, press select switch
* When the select switch is pressed while the digital display is showing the time. The turbo timer will then display either P-1 or P-2.
* When the select switch is pressed while the digital display is showing the time. The turbo timer will then display either P-1 or P-2.
* When the select switch is pressed while the digital display is showing the time. The turbo timer will then display either P-1 or P-2.



How to turn the sound off

By pressing and holding down the power switch while the turbo timer is ON, you can turn the sound ON and OFF.
1. Turn the POWER on.
2. Hold the POWER switch button for 2-3 seconds
3. Then the Turbo Timer will make a single beep, indicating that the Turbo Timer's sound mode is either turned on or off

I use this timer for my Daihatsu Mira L502 engine.
Download diagram ECU for speed signal
Thanks For this website
Greddy Timer

No comments:

Post a Comment

Thanks For Your Comments

Subscribe to: Post Comments (Atom)